Seats

And now there's somewhere to sit. The seats are 6 by 1 ¼ inch wide slats of Sapele, given 4 good coats of garden furniture oil.

I'm putting cross braces underneath the slats half way between each pair of frames. This means the 6 slats move together. I makes them much stronger.

Is that sharp enough

I've got most of the slated seats done. I'd have them finished tonight only it's raining, so I'm here typing. And I've started on the coamings. Since I've only just enough wood, I am being kind of careful not to cut anything too short. Given the complex joins, with compound angles, I cut the first one 1/8" too long on purpose, intending to sneak up on it with a plane.

Damn, end grain in Sapele is as hard as a Hamiltonian Path. (really hard)

I think it was Lincoln who said "If I had six hours to chop down a tree, I'd spend the first four hours sharpening the axe", well I sharpened my little low angle block plane till it could do this to the end grain.

Good man Lincoln, with sense like that, he should have been let run the county.

The obligatory birds mouth test

I'm still thinking of doing a hollow mast. I made up a quick jig on an 18v hand saw to cut the groove in a single batten, then I cut this into 8 pieces.

Even with this rough and ready attempt, it came out rather well. Go to Duckworks website and search for Birdsmouth. They have LOTS.

I penciled in the outline of the joints, othersiwe you could hardly see them.

Introducing the Lady Caroline

Now that the deck is glued into place, and trimmed, I can see what The Lady Caroline will look like.

I've just started the seats. I have some filling over the screws & sanding to do on the deck.

It's all coming together.

In other news, my Mom recycled an Old Leather Sofa. I acquired large amounts of the leather. And a short strip of it made a nice strop. Turns out that a scrap of leather with some polishing compound on a backing of birch ply will sharpen up a blade just fine. The more I practice sharpening tools, the more I wonder what all the fuss is about.

The deck is attached.

The entire deck is now glued and screwed in place. It started raining about 10 minutes after I'd finished the aft panel. That could have been a small disaster if the rain has arrived 30 minutes earlier.

I see a router and an edge trim bit in my near future to trim back the over hang on the deck.

I've started work on the seats. The slats look really nice with the deck oil on them. I just broke the corners with sand paper. The wood has a wavy grain, back and forth a few mm every few feet. Fine in terms of the strength of the slats, but running a block plane along the edge is a disaster. 18" of slicing through the grain followed by lifting a chunk.

To bend the slats into place, I've clamped a block to the outside of the seat supports, and reversed a few QuickClamps to make pushers out of them. An extra one vertically placed at each end keeps things from springing loose.

I've just sanded and oiled two slats so far to see how it goes, now I need a more efficient way of doing the remaining 12 for the seats, and 9 for the floor.

A picture during the day

I took Wednesday off to do some family stuff, but I still had time for a little boat work when the littlest one was asleep.

I've rough cut all the panels for the deck. They are all epoxies on one side, the other sides next on the list.

Then I start to glue & screw it down.

You can see the slats for the seats sitting in the boat.

Sorry it's a little... untidy. My workshop consists of two D&B workbenches side by side.

Today I started the deck...

I have already rough cut the 5 pieces that will make up the deck. But now the framing is completed, screwed, glued and dried.

So I've finally started work on the deck proper.

I've cut the backing blocks for the butt joints.

All the main pieces are rough cut and I've gotten one side of each soaked in epoxy. (much easier to do now rather than climbing inside later.)

I've started screwing the fore deck in place and laying out the remaining part to mark them up.

I really feels like I may have a boat soon.

D

Oak is sharp !

The deck framing is now almost complete. I've one or two dovetails to cut, and I've almost all the fairing done.

One thing that I learned is that white oak chines, when planed, can be sharp enough to remove chunks of skin. You always remember not to have a hand in front of a blade, in case the blade slips. But I forgot that a 60° oak edge is just as much a blade to the soft skin on the side of your hands.

To avoid anyone unnecessarily setting up a "Save Dave" web site, and associated charities to pay my hospital bills, I should say that my hands are still fully functioning, the missing skin didn't require any more than a plaster.

One other thing that I spotted is that before I screw in the last few pieces, It will be a lot easier to measure and mark the coamings. I can cut them to roughly fit, and mark them exactly in place. If I screw and glue the remaining pieces first, then I won't have that option.

All going well, I'll get the coamings and other details sorted this week during the evenings, and start the deck next weekend.

That bit looks big enough

So I wandered out to the boat last night after the munchkins went to bed, and I spent a while looking at the place where a cross member needed to go, and trying to figure out if I could laminate up a piece, since I didn't appear to have a piece big enough. I wanted to avoid another long trip to get one plank, when I noticed a piece that I'd tucked away under the boat a while back.....

Looks just about right, hold it in place, clamp a few bits in place, mark it up, double check everything (all under a battery powered florescent inspection lamp and a head torch) and whip out my Pull Saw. I can now cut compound bevels to a line as accurately as I can see. You got to love pull saws.

(I came across a small article in a magazine a while back about cutting a starting notch for the saw with a stanley knife. Make it 1/4" deep by paring the waste side down, and you have a perfect guide to start the cut.)

I can't fire up power tools late at night, the neighbours would (quite reasonably) be peeved, but no-one seems to mind the nutter with the hand saw and the head torch.

Anyhow, in an hour or so, I went from planing to spend an hour on Saturday cutting and laminating a piece to simply having it cut to length and fitted.

I've marked off the curve for the top of the piece too. I'll run it through the band saw later this week.
I can run the band saw after dark, it barely makes any noise as it slices through 1" of white oak... which is kind of scary in a way. At least a table saw screams a dire warning that's pretty hard to ignore. The band saw just quietly cuts through pretty much anything.

Can we go sailing now daddy?

"Is it finished yet?"

"Daddy, when can we go sailing?"

"Can we go sailing tomorrow?"

"When can we go sailing?"

And the winning question from my 3 year old daughter....

"Will I be older then?"

The Cut.....

So I have 2 pieces of oak, 3" x 1" x 10' for the Carlings. (good luck finding that on Google without coming up with larger, or sports - try "Carling and Deck)

All I have to do it cut them to fit.

At each end, there's a compound bevel. And the wood curves along the length of the boat. So if you don't take account of the curve, it will end up short.

You can see here how you cut the angle to get the length right.

I was accurate to about 1/10" over 9 foot on one side, and a snug fit on the other.

Measuring and marking the wood in place, if you can, it easily the most accurate, and least error prone way of doing things.

Making Sawdust....

The last consignment of wood arrived yesterday, so I took a days holidays to.... get the wood tidied away out of the house.... yes. Get it Tidied....

I have a cheapo shop vac that I can connect up to the power tools, after ripping various oak and mahogany planks into over 20 1", 2", 3" and 4" wide slats, each over 9' long, I had enough sawdust to fill a large kitchen bin.

I now have all the wood I need to finish the boat. All I need now is time and good weather.

I now have to round the edges of over 400 feet of wood. And then Oil it all.

I'm going with deck oil rather than varnish. It's more continuous maintenance, but the maintenance is a lot easier. Just rub in more oil. No Sanding, stripping back to the wood. Just rub in more oil every 6 months and you're done.

D

A weekend of progress...

I got out my Bevelator 1000 again. This time to bevel the sheer clamps where the deck will go on. I also cut 2 of the three beams that will sit under the foredeck.

The remaining wood arrives over the next week or so. So I should have a deck on the boat in the next 3 weeks.

Then it's the seats & floors.

I found this for making up foils. Nearly as good as a 3d Cad system.

New Toys....

Against the day that I might actually have to sail the thing, I've started accumulating various bits and pieces that I'll eventually need.

I picked up a marine compass a while back, and a last week I came across this http://www.opticron.co.uk/Pages/trailfinder_ii.htm

Note the Inter Pupillary Distance. 58~77mm. For those who can't get a one size fits all baseball hat to fit, the normal ~72 mm IPD on binoculars leaves you with a very cumbersome monocular, with a spare attached.

Many of the other Binocs with a large IPD were Lecia or Swaroski or Steiner, and the prices were quite exotic.

If you are to look through both eyes at the same time, these may be worth a look, so to say.

The are (to my unpractised eye), pretty good, solid, the focus mechanism is reassuringly free of play, and they have a 5 year guarantee.

I don't have any real experience with Optics, so someone more knowledgeable may pour scorn on my advice, but two eyes able to see at the same time is a huge improvement.

I would have preferred the traditional 7x50, but they were ~74mm IPD, and I could not try them out locally.

Snow ?

This is Ireland, we get 3 or 4 flakes of snow each year. That's it. Unless you are up the "mountains" (hills) and you might get enough to make a very short snowman.

This year we had several inches, and real cold. Not the 2 Celsius (35 F) that we usually get, we were getting -10 Celsius (14 F).

I took my 3 year old out on a sleigh. She loved it till she got cold.

People's pipes froze, and burst. Lakes froze over. Some people I work with took 5 hours to get home.

All this means that I have done very little on the boat since I took the pictures.

I've sharpened a few hand tools, and read a lot, but real no progress.

Pictures at last

As I could now put it in the water, and get in, and it would float, I now claim it's an unfinished boat. It is no longer a pile of sticks.

I’ve started painting the inside.

I’m painting at night, in the cold, with a site lamp and a head torch. I must look even stranger than usual.

One thing I realised is that when you have lots of battens, chines, frames etc to paint, you get a lot less than the advertised coverage for a tin of paint. They assume you are painting a large flat area. When you have to work in nooks and crannies, expect to get about half the coverage.

I’m using Blake’s (now Hemple) paints. The inside is coated with epoxy, then white primer and then 2 (soon to be 3) coats of pale cream multicoat.

It is starting to look pretty well.

Just a brief update

The boat is now upright on a combi trailer.

I have two tent poles across the boat holding up a Tarp.

The inside is now sealed with epoxy.

Sanding and painting starts next.

I'm still in two minds about adding a buoyancy compartment forward and aft, or just using buoyancy bags, or using foam slabs.

Thanks Guys

It was like a weird and wonderful Team Building Exercise.

All we had to do was move the boat from the back garden to the front garden.

The boat has a 6' beam. The lane between the houses is about 6'10". Plenty of room.

The fun bit was the 4'-5' high wall running down the middle of the lane.

We had a short false start where we were still bolted to the ground (my Fault, sorry guys).

Then the 7 of us lifted the boat to shoulder height and manoeuvred it up over the wall (sorry about the plants Caroline.)

I somehow ended up standing underneath the upturned hull, with my shoulders to the frame. It was my first real view of the inside.

We did our best to cripple my soon to be wed brother, by trying to drag him across the wall through a bush, but he was having none of it.

The Herculean Effort culminated in The Lady Caroline* being man handled into place, in the front garden and then carefully flipped over.

So Thanks Guys, In Alphabetical order Alan, Andrew, Colum, Connor, Oliver and Peter.

And thanks Andy and Trish for letting us use your garden in the move. I hope Bonnie forgives us for locking her in the kennel throughout.

And thanks again to Caroline, my wife for putting up with this, the boat, the mess, the invasion of the house, the time spent, etc. etc. etc.

* The boat, not my wife.

From the Air

This is from google maps.

You can clearly see the blue tarp that covers the boat in my back yard.

Yes, it will fit out between the houses.

(I hope)