Tuesday, July 31, 2012

A little about welding..

Some good books

  • Farm and Workshop Welding
  • How to Weld: Techniques and Tips for Beginners and Pros (Motorbooks Workshop)

Phases of not being able to weld (just stick welding mild steel - lets not get silly just yet)

  • Can't strike an ark
  • Can't run a bead
  • Can't run a neat bead
  • Bead is (too high,  too flat, undercuts the metal, laced with inclusions)
  • Can't join metal at all
  • Can break metal about with bare hands
  • Can break metal with hammer
  • Can sometimes break metal with hammer
  • *Can't make neat weld to join metal
  • Can't always make neat weld
  • Take a lot of attempts to dial in the right settings on a different type of joint.
If I get past this list, I'll consider my self to be about "beginner" status.

I guess it's true of so many things. They seem simple until you start to learn about them, and then you find out how much is involved.

Some Simple Ideas 

(Bear in mind I'm an utter novice, so this has very little authority behind it) 

Too cold, you only join the surface. Too hot you burn through.

Too Hot, Speed Up to compensate, and you don't deposit enough metal, you get undercutting.

Too Cold, Slow down to compensate, you end up with too much metal, and inclusions from the slag getting around you.

As you run a weld, the metal heats up, at the start it's stone code. Circle at start for a second before you start moving.

On thin stuff you need to do short welds, then let it cool. Repeat.

More weld material does not make a weld stronger, a nice convex fillet is stronger than a blob as the blob introduces a sudden change in thickness of metal, which is a stress point. The weld is stronger, the joint is weaker. It will break at the edge of the blob.

Buy an automatic helmet. As a beginner this makes a lot of difference.

* I'm about here, on a good day. With varying degrees of the preceding problems.

Monday, May 07, 2012

And now I'm learning to weld...

It's a long way from boats, but I'm planning on building a recumbent bike. See http://www.atomiczombie.com/

I've started learning to weld, there's tonnes of stuff out there, the good the bad and the ugly. Some of it is just plain wrong. The dedicated sites are better than instructables & such.




 Ymmv, given that I don't know a whole pile about welding, do take my recommendations with a whole pile of salt.

Tuesday, November 29, 2011

Winter List

No boat is ever finished, and I have my list for the winter....


  • Brass rubbing strips on the rudder, centreboard and the front of the hull
  • Cargo Netting for bits and pieces
  • Fix the bow eye, it was too small and it bent
  • Add a nose wheel to the launching trolley
  • Add a winch to the trailer or trolley. This needs some thought, I want to make it easier to get the boat onto the trolley and the trolley onto the road trailer.
  • Wooden Trim where the hull joins the deck. More sanding.
  • Reapply oil to the seats, coamings etc.
  • Put the wooden bungs in the screw holes in the coamings.
  • Lazy jacks / topping lift
  • See if I can improve set up time for the mast / sails. I think if I have something to support the stern while on the trolley, I can raise the mast by hand. We shall see.
  • A mount for the GPS
  • Bilge pump (or pumps) that I can use on either tack.
  • A better way of stowing the outboard while towing.
There. Now I have a list.

It's longer than I thought it would be, but it'll get longer yet, lists always do.

Sunday, November 06, 2011

Sailing in November

My wife's family is from Cavan, and my parents have retired there too. So, on Friday we drove to Cavan, with the boat in tow. While my wife and the children visited her parents, I met my parents at the lake with the boat. (Thank you my love for the time you give me to sail.)

The lake was up about 4 - 6 feet over it's banks, which meant the car park was flooded to 18 inches. So I had to push the boat and trailer right through the (bitterly cold) water in the car park to get deep enough to launch it.

I'm now in my 40s, so Mom's claim to being 21 is not looking good, but she rolled up her trousers and waded knee deep into the lake to climb on board.

Her father was a Ship Builder in Arklow, and this was her first time going out sailing in a boat built by her son. The world turns.

It was also only my third time out in the boat. So her faith in me may be misplaced.

Using an A Frame, an open hinge, and temporary, sprung stays, I've hugely simplified hoisting the mast and setting up the boat, but it still takes about an hour. This time, I rigged the Jib for the first time. Up to now I'd only be flying the mainsail.

The lake was divided into regions of small waves, ripples, and of glass, depending on the lay of the land, and the shelter of the trees.

As you can see the lake is somewhat convoluted.


View Larger Map
Our journey went from the Bridge marked A above to the turn in the lake and back. Hardly an epic voyage, but an adventure nonetheless.
For the first time I popped up the Jib. It's on a rolling furler, and it was far easier to fly it and later stow it again than I'd expected.

Mom took the helm for a while, and we generally took it easy. In spite of it being the start of November, it was surprisingly warm, and the sky was blue, barely dotted with clouds.

At one point we tacked back and forth a few times to clear a copse of sunken trees whose crowns were barely half clear of the water. With a pivoting centreboard, and pop up rudder, I fear no shallows, but tangling with those trees could have left us stuck, but in deep enough water that getting out to push off was not an option.

I had not turned on the GPS so I've no idea how fast we were going. It was light enough air that we could sit one each side and sail without any concern of capsizing. There was a noticeable increase in speed when we flew the Jib. At times we "flew along", but when we passed through the shadows of the trees, we had to look at our wake to be sure we were moving at all.

The return to our launch site was narrow, close to the wind, and in shelter. After slowing to a halt and drifting back and sideways twice, I relented and used the outboard engine to take us in to where I could jump out

I'd like to say a big thanks to my father, who in spite of not having any wish to board any boat which is not large enough to have a choice of restaurants, did help me set up and tear down the boat, and sat reading in the car awaiting our safe return.

These lakes will be my sailing grounds for a while, and there's more than enough to explore. As the kids get older, there's plenty of "pirate coves" and "magic islands". I think I'll need to order "The Swallows and The Amazons".

Monday, September 26, 2011

A new toy

I picked up a Ceramic Folding Knife on the internet. $49 + $5 postage - from Canada to Ireland. Nice, usually postage makes things like that prohibitively expensive.

You can see them at http://www.ceramicknife.org/


It's about as sharp as you will make a steel knife without taking a strop to it. That is it slices paper like all the demos you see on youtube, it won't shave the hair off the back of your arm, but, it will slice through 8mm poly double braid without any fuss at all. (Which is more important than shaving your arm bald!)

The handle is stainless, the blade is ceramic. It's held together with tiny recessed bolts, so you can take the whole thing apart if you even need to. (Not that there's anything to go wrong).

It clicks closed, so it won't pop open accidentally. And it locks open.

It feels light, but not in any way flimsy. It takes a little practice to pop it open without your thumb getting too close to the blade, it sort of pops, and your thumb can slip of the stud. The blade is only an inch wide, if the back of the blade was a bit wider, there'd be more room for the thumb stud.

On the whole a very nice toy. I can't help thinking my modified Myrchin will still be my go too knife on the boat, 'cause I know it's bullet proof. But I suspect that this one will have it's place too. I just want to see how resilient it is.



But on the whole nice toy.




Sunday, September 25, 2011

Cutting Rope

I have a Myrchin P300 knife. It's really quite nice. But the serrations are very aggressive.
This means that

  1. It catches in the rope if you try to cut rope.
  2. I can't sharpen it very well (ymmv)
  3. At the end of it all, I take 3 serious attempts to cut 8mm double braid.
I have a small Leatherman and it has a plain blade and a serrated blade.  The plain blade will take an edge which cuts through 8mm double braid like it was wet tissue. The serrated blade, having shallow scallops, does the same, and is easy to sharpen. But it's fiddly to open, needing two warm dry hands.

So I got out my coarse diamond stones, and ground down the serrations on the Myrchin until they were less like a comb! Then I sharpened it (with a spyderco sharpmaker), and just because I could, I honed the blade on a cheapo cloth wheel powered by a drill with some polishing compound.

My Myrchin now cuts through the 8mm poly with callous disregarding ease. It sits nicely in my pocket, it has a pliers, and a locking marlin spike. And now it has the blade that I'd have put on it. It does not look nearly as scary as the original blade. But when your hands are cold, you are tired, and something is tangled, if you want to "untangle" it, you don't care much for how scary the blade looks.

Monday, September 19, 2011

Well that didn't suck !

The wooden pump sucks water just fine, provided that it's either in water, or primed. It won't self prime more than about 3" or so. I could see the water climb about 3" through the clear plastic hose. No More.

I guess that while the clearance of the piston, and the valves was just fine for water, air just flows past them. I could do a better job, and add seals, and improve the valves, but now the engineering is starting to get to the stage where it's very time consuming, and fragile.

So, I'm just glad that I only made a mock-up, and did not spend a lot of time making it pretty.

Oh well.

Some you win.

Monday, September 12, 2011

A wooden Pump

I can't claim credit for this, I found it here at duckworks (thanks By Tim Ingersoll - Superior, Wisconsin - USA) but I thought it would look a lot better on my boat than a grey / black plastic thingy.

I cobbled one together out of scrap plywood to see if it simply functioned. I didn't want to spend a lot of time and effort and expensive wood to find out that it trickled water out, or had to be made to perfect tolerances.

It was easy to make, it moves LOTS of water with very little effort. It does splash water out the top where the handle comes out, so I need to try to make a "seal" there with rubber.

I need to try it with a pipe out the bottom to see how well it primes, but I think I will be putting my whale gusher urchin up on ebay shortly.

If it will self prime well enough, I see one each side of the boat, with a pipe to the other side, so that I can pump out the boat while I'm on the windward side.

Photos and test results for self priming to follow. But I've a Math project to hand up, so it may be a little while.

Monday, August 29, 2011

Some things that I wish I had known before I started.

Don't underestimate the importance of setup time on a small boat. Sloops have tall masts, which are more effort to build, set up, and store. Gaff / Lug rigged boats have multiple, but smaller spars. Often fitting right inside the boat itself for storage / trailering.

Every Cotter Pin you need to put in place, with a tiny, fiddly split ring takes more time, especially with cold tired hands. (And bring lots of spare cotter pins, in every size, and lots of split rings)

The more open space in a boat, the more water it can take on. Boats with seats which are storage / buoyancy compartments take on a lot less water than simple park bench seats. I may, over the winter refit my seats, it will be a lot of work, but it would give me tremendous extra buoyancy and storage, and massively reduce the amount of water I'd have to bail out in a swamping.

I should have turned the front frame into a bulkhead. The space forward,  is more or less useless to me. It's too far forward to store anything. It's now filled with a GYM ball as buoyancy. With a bulkhead, and an pair of waterproof, lockable access hatches from the deck, it could be used for storage of light, infrequently needed items. And it would still represent a lot of buoyancy.

I should have bought a trailer with room for a winch. Pulling the dolly up onto the trailer is awkward, and when you haul at it, it can come flying forward. A winch would be far more controllable

I should have turned the frame just under the fore deck into a bulkhead, and put in large hatches. Lockable storage !! Dry storage !! More stuff that I could leave on the boat, ready to go, rather than have to keep it in the house/shed. Again, a shorter "time to water"..

Sunday, August 21, 2011

Quick Sailing Clip

Ok, so I need a whole lot of practice.


  • To get off a shallow lee shore, stick one foot on board, hold the tiller centred, and shove a few times with your other foot like you were on a child's scooter.
  • Don't lower the mast in a cross wind. Really, Don't 



 

Saturday, August 20, 2011

A little better....

It's amazing how much better she sails with a functional centreboard. Gravel is a bad thing for pivoting centreboards.

On our second trip, a quick spin around some lakes in Cavan, was a whole lot better. The engine remained unused. I sailed a short loop on my own to ensure all was well, then took Sarah and Abigail each for a spin, under sail.

I remembered reading an article where a sailing Uncle strongly advised short trips, far better to have the kids complaining about going home too soon, than sitting there frowning, saying are we going home yet.

My sailing skills are currently the limiting factor, but with just the main, in a light breeze, she scooted along at just shy of 4 knots. Almost exactly 4 miles an hour, so about walking speed.

I am reasonably sure that any competent dinghy sailor would cringe at the rudimentary mistakes I was making, but hey I have a boat now, I can learn.

Oh yes, the kickup rudder, worth it's weight in gold. I cannot imagine the damage I would have done by now, beaching TLC several times, only to hear the sharp Snap of the auto- release-cleat opening. I certainly would not have been able to lift the rudder, while trying to steer the boat, and manage the sails. Perhaps with a few years practice, but for now, thanks Duckworks!!

http://www.duckworksbbs.com/hardware/cleats/sd002570/index.htm

Tuesday, August 16, 2011

The Launch Video

Ok, so not quite a master class in sailing, but she floats, she sails, and she motors.


Ready to rock

A quick snap of the boat on her trailer


Monday, August 15, 2011

Not quite a Master Class in sailing....

On Sunday I launched The Lady Caroline.

I had the assistance of Ben, and the patience of his whole family who came along to join us.

The boat floated, upright, and no-one drowned.

We even got to the stage where we were confident enough to bring his kids for a spin around the estuary with the sails down, just running the outboard.

Before much more ado, A HUGE Thanks to Ben and Family. Ben and Sarah's patience when they got a lot more than he bargained for was nothing short of astounding.

We did make some pretty good decisions, which resulted in my poor decisions not getting out of hand.

  • We launched in a sheltered estuary.
  • We brought an anchor, chain, and rope
  • We had an outboard.
We also learned


  • It took a LOT longer to setup and tear down than I expected.
  • Gravel makes a bad launch place for a sailboat with a swinging centreboard.
  • When the CB is stuck up because it's jammed with gravel, you cannot sail upwind, in fact, you cannot even turn upwind, you have no pivot point.
  • Leaving a hole in the CB case cover so that you can push down the CB is a good plan
  • Forgetting to bring a long thin stick to push down the CB is not.
  • An outboard helps when you can't sail
  • Too much choke is as bad as too little.
  • An anchor allows you to STOP and think and fix things without panic.
  • The concrete wall long beside the slip continues underwater a lot further than you'd think.
  • Old fashioned boats without a plumb bow tend to ride up on underwater concrete walls without too much damage.
  • Self-bailers are no good if you can't reach them without lifting the floorboards.
The suzi 2.5hp was more than enough power, but the movable bracket is set too low, so part of the bracket drags in the water. Not a big deal, but annoying, I need to sort that.

We did get a little sailing done, a broad reach with the mainsail reefed.

All in all, a success, but I need a LOT of practice sailing.

Video Clips will follow once I get them edited & uploaded.

Dave

Thursday, August 11, 2011

Weather Watch.....

I am now watching the forecast for a suitable date to Launch The Lady Caroline.

The last of the "necessary" jobs are done.

I have still some nice to haves, but I gather than when you have a boat, the todo list never goes to Zero

I have a few things to get, including a stout bucket for bailing.

But Ultimately, I'm ready to go sailing.


Thursday, August 04, 2011

More or less ready

I have put in most of the Buoyancy, I have just the bow bag to do. (1 evening)

I have finished the fittings, including the self-bailers.

I have still to put on 3 mooring cleats, (2 bolts & 1 backing plate each - 1 evening for the three)

And to sort out the trailer board for towing, (1 evening)
and a holder for the mast. (? not sure about this)

I'm now gathering things like a paddle, flares, Life Jackets, a bucket, etc to get the boat ready.

But I'm, no longer building a boat, now I'm getting it ready for launch.

Watch this space for photos in the water.
And maybe even a short video or two.

Sadly, I do realise that I will have to do a capsize test, and an swamping test. Neither of these are going to be a whole lot of fun. I'm thinking wet suits and a sunny day, which may mean next season.

D

Tuesday, August 02, 2011

Our Survey Said....

The boat is now surveyed (a requirement for the insurance) and the surveyor has declared it "built to a very good standard of workmanship"

Ps, A word to the wise, plan where the deck fittings will go before you put in any screws which might be in the way. Otherwise Sods law will ensure that you have drilled 3 of the 4 holes to mount a fitting before you find a screw in the way of the final hole...

Sunday, July 31, 2011

there's just a few more things

The engine mounts is done. Since the transom is angled, I made a rookie mistake and set the mount too low, then I had to fill the bolt holes and re-mount it higher. (Luckily I popped the engine into place with the mount dry fitted,  so at least I didn't have to clean up bedding compound.)

The Self Bailers are dry fitted. If you are ever mounting these, it's hard to drill holes square to the hull while lying on you back reaching under the trailer. So drill the holes from the side where they go through the bailer. (ie if it's an outside mount, drill from outside) otherwise it's hard to get things to line up.
It does take a moment to get up the courage to cut a big hole in the bottom of your boat. I did make up a test piece first with some scrap.

The bracket for the Jib was fun to mount. It is thru-bolted. Of course that means that you need to climb into the bow to put on and tighten the nuts. A 6'4" tall 200 lb man can fit in past the centerboard case, and under the deck. But for a few minutes, it was entirely unclear if the same man could climb back out again.

Thanks to Caroline for holding the screwdriver outside while I crawled inside.

(Yes, she is smaller, and would have fit easier into the bow, but there is a limit to how far I was prepared to push my luck.)

Tuesday, July 26, 2011

The weather got better, so I got some stuff done.


1 more coat of paint(1 evening)
*Flip her over and back onto the trailer(1 evening) Thanks Alan !
Bedding compound for the mast track & fittings (1 evening)  
Mount the rudder (1 evening)


Mount the Engine (1 evening)
Fit the drain plugs / self drainers (1 evening)
Mount the Hardware for the forstay and Jib (1 evening)



+ Repaint the deck, it looks pretty grubby.


This weekend is looking touch & go, but it's getting close....


* It's amazing what you can do with a ground anchor* (think gigantic corkscrew), a whole lot of rope, an A-Frame, and a figure of 8 descender, and a few double blocks. Oh yes, and a few packs of rubber kids play tiles to keep from scratching the paint to bits.


** Trees make good anchors too. Anything 10" in diameter or so is not going to budge under any loading I'm likely to apply.

Friday, July 15, 2011

The Lady Caroline in a Blue Dress


I finished painting, and had her covered about 3 minutes before a small shower. One more coat and she's going for a swim.

The todo list is down to

1 more coat of paint(1 evening)
Flip her over and back onto the trailer(1 evening)
Bedding compound for the mast track & fittings (1 evening)
Mount the Hardware for the forstay and Jib (1 evening)
Mount the rudder (1 evening)
Mount the Engine (1 evening)
Fit the drain plugs / self drainers (1 evening)

I also need to fit wooden trim/bumpers, but they can be added after her first sail.
Posted by Picasa